Can I Install A Bath Tub Myself?
Can I Install A Bath Tub Myself?
Blog Article
Do you find yourself trying to find advise concerning Tools You Need to Install a New Bathtub ?
Setting up a bath tub isn't exactly brain surgery, yet it does require solid plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably difficult project. If the old bathtub is conveniently accessible, the project can move immediately; if you have to open up a wall surface to remove the old tub as well as place the brand-new bathtub, the task is much harder. In either situation, the task is within a residence handyman's skills, although you will need an assistant to vacate the old bathtub and also set in the new one. See to it you have actually certified yourself for the task and also fit attempting it. Rather than hiring a specialist to take over a halfway-completed job, it is much better to take into consideration using one prior to you start. Chances are you may need a professional plumber to make tube connections.
This short article will assist you set up a new tub in your restroom if you have already acquired a brand-new bathtub and also do not require to alter the plan of your previous supply of water pipes.
Your tools as well as material checklist should comprise the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, after that the first thing you must do is detach the water system. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The procedure of removing the existing taps can be fairly troublesome because of the restricted accessibility that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a fabric prepared for the remaining water that will certainly originate from the pipes. As soon as the supply pipelines have been removed, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing substance.
Prior to proceeding to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in place in between the tap as well as the sink. Secure the tap in position with the manufacturer supplied backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The former kind should be linked to the faucet ends initially, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Utilizing both wood boards under its feet, put the bath tub in the called for position. The wood boards are useful in equally spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The next objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the tub till the level reads level.
To mount faucets, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression join; then do the exact same for the various other faucet.
Activate the water supply as well as inspect all joints and also brand-new pipework for leaks as well as tighten them if needed. Load the bath tub as well as also check the overflow outlet as well as the typical electrical outlet for leakages.
Finally, repair the bathroom paneling as defined in the supplier's instruction manual. Tiling and also sealing around the tub must wait till the bath tub has actually been used a minimum of when as this will settle it right into its last placement.
Planning for the Installment
Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to make certain that if the faucet includes a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its final placement.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, causing the water to pass through the wall in between the bath and the tiling, bring about issues with dampness and also possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also installations. They are sold in tubes and also cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the bath tub with water before securing, to allow for the activity experienced when the tub remains in use. The sealer can crack relatively early if you do not think about this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily offered on the marketplace. It is recommended to fit the floor tiles using waterproof or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen reader about Installing A Bathtub, I figured sharing that piece of writing was a good idea. Enjoyed our content? Please share it. Let somebody else locate it. Thank you for your time. Visit again soon.
Need Help? Hire Us Now!
Report this page